Superstructures for single-tooth implants
2010/2/28 来源:网络
In modern dental implantology, aesthetics are becoming increasingly important. Improved aesthetic results can be achieved as a result of the wider variety of materials, designs and techniques available for implant restorations today. There is also a wider selection of implant abutments, including CAD/CAM, UCLA and prefabricated abutments made of different materials such as zirconia, titanium and gold. This article describes singletooth implant cases in which aesthetic superstructures were success-fully fabricated with the IPS d.SIGN■ layering ceramic system.
In order to achieve a natural shape and contour of implant restorations, profound knowledge of the anatomy of teeth and the gingival outline is necessary. A careful examination of the horizontal sections of teeth (Fig 1) reveals that each section is unique and has a different appearance. Ceramists should consider these unique charac-teristics of dental anatomy in order to achieve a natural emergence profile which is in harmony with that of the adjacent teeth (Fig 2).
A customized abutment (UCLA abutment) must mimic the shape and contour of the natural tooth. In this case, the abutment was cast in gold and a ceramic shoulder was applied using IPS d.SIGN materials (Fig 3). In order to ensure a natural-looking gingival outline, the gingival contour on the working model had to be modified (Fig 4). After the fabrication of the customized abutment, the metal framework was created based on a reduced full-contour wax-up (Figs 5 and 6). Prior to veneering with IPS d.SIGN layering materials, the surfaces of the metal frameworks were carefully finished using crosscut tungsten carbide or ceramic-bonded burs. After having blasted the frameworks with 100 μaluminium oxide at two bar pressure and steam-cleaning them, they were ready for the first wash firing or the actual opaquer firing cycle (Figs 7 and 8).
Summary
When fabricating restorations, it is important to imitate the features of natural teeth. The root and the shape in the cervical area require particular attention when implant-borne restorations are made. Never -theless, the fabrication of implant-retained restorations has been difficult to date, as the metal imposes certain limitations.
Fortunately, a number of manufacturers have developed new materials which open up new possibilities and thus enable results to be achieved that are satisfactory for all the parties involved.
In particular the IPS d.SIGN materials provide outstanding properties which allow the natural tooth shade to be precisely mimicked (Figs 19 and 20).
Consequently, the fabrication of aesthetically pleasing, implant-supported restorations has become considerably easier, as suitable materials are available for each individual case




In order to achieve a natural shape and contour of implant restorations, profound knowledge of the anatomy of teeth and the gingival outline is necessary. A careful examination of the horizontal sections of teeth (Fig 1) reveals that each section is unique and has a different appearance. Ceramists should consider these unique charac-teristics of dental anatomy in order to achieve a natural emergence profile which is in harmony with that of the adjacent teeth (Fig 2).
A customized abutment (UCLA abutment) must mimic the shape and contour of the natural tooth. In this case, the abutment was cast in gold and a ceramic shoulder was applied using IPS d.SIGN materials (Fig 3). In order to ensure a natural-looking gingival outline, the gingival contour on the working model had to be modified (Fig 4). After the fabrication of the customized abutment, the metal framework was created based on a reduced full-contour wax-up (Figs 5 and 6). Prior to veneering with IPS d.SIGN layering materials, the surfaces of the metal frameworks were carefully finished using crosscut tungsten carbide or ceramic-bonded burs. After having blasted the frameworks with 100 μaluminium oxide at two bar pressure and steam-cleaning them, they were ready for the first wash firing or the actual opaquer firing cycle (Figs 7 and 8).



Following this,the fluorapatite glass ceramic materials were built up. After contouring and finishing, surface texture was applied. Finally the restoration was glazed and polished. This is only briefly shown here by means of the Figures 9 to 18.
Summary
When fabricating restorations, it is important to imitate the features of natural teeth. The root and the shape in the cervical area require particular attention when implant-borne restorations are made. Never -theless, the fabrication of implant-retained restorations has been difficult to date, as the metal imposes certain limitations.
Fortunately, a number of manufacturers have developed new materials which open up new possibilities and thus enable results to be achieved that are satisfactory for all the parties involved.
In particular the IPS d.SIGN materials provide outstanding properties which allow the natural tooth shade to be precisely mimicked (Figs 19 and 20).
Consequently, the fabrication of aesthetically pleasing, implant-supported restorations has become considerably easier, as suitable materials are available for each individual case
本文相关关键词:
相关推荐
-
明星牙齿矫正
(我要八卦) 种植牙病例 - 牙齿矫正病例 - 烤瓷牙病例 - 明星牙齿矫正 -
跳水皇后吴敏霞曾是龅牙妹
全民女神高圆圆做牙齿矫正对比图
小魔女赫敏牙齿矫正后智慧与美貌并存- 牙病大全问题分类
- 共提问问题数: 35114 次
- 已解决问题数: 28386 次
- 烤瓷牙咨询 有 4687 人咨询
- 牙齿矫正咨询 有 6197 人咨询
- 种植牙咨询 有 2106 人咨询
- 根管治疗咨询 有 2597 人咨询
- 牙齿美白咨询 有 2034 人咨询
- 补牙镶牙咨询 有 4908 人咨询
- 牙周病咨询 有 1616 人咨询
- 其它牙病咨询 有 4194 人咨询
- 投诉与曝料咨询 有 46 人咨询
- 进入咨询在线答疑
牙大师手机站 | 落深圳睇牙 | 深圳睇牙分類 | 牙齿问答 | 关于牙大师 | 免责声明 | 删稿需知 | 官方微博 | 网站地图 | 牙科网站建设Copyright © 2000-2026 www.yadashi.com 版权所有 微信公众号:yadashicom
广东省口腔医师互联网协会会员单位 深圳市互联网协会会员单位 深圳市互联网技术应用协会会员单位
本站为口腔健康科普与就医信息服务网站,站内内容由本站编辑部整理、编辑与校对。部分资料参考自公开出版物与网络公开信息,涉及第三方内容的均已在文中注明来源。
所有内容仅供健康科普参考,不能替代面诊、检查与专业诊断,请以执业医师的当面诊疗意见为准。
内容纠错与版权事宜,请联系QQ:498810094














